More table details, June 5 2016

Here are some more details on the table top

 Here is the support mounted on the wall

Table installed

Close up of support with table inserted. I wanted the small storage area with fiddles to hold water glasses,,salt and pepper, and other stuff that is handy to have at the table. The other point is that it pushes the table a bit out into the aisle, so it looks right on the leg (if flush to the wall, the leg would stick out past the edge of the table)

Saloon puzzle

Here is the completed picture of the saloon with the settee pulled in and the dinette folded down. After I took this picture I rounded some corners. Still to come is the lean back storage, and of course the walls and windows.

And here is a detail of the table leg in the down position, with the added plywood bits

 And here is the same leg in the upright position

Hopefully I have the photo editing figured out, and you can make sense of what I was trying to do here

A quick word on "Good Enough"

The working name for the triloboat I am building is "Good Enough", as in something that is good enough to get the job done properly, without regard for superfluous additions. I ran across a link to a boating blog with some similar thoughts and thought I would share.
If something is "Good Enough", it is not mediocre, but neither is it gold plated. Perfection is the enemy of Good Enough, life is too short to waste trying to build something perfect, as then there would be no time left to go sailing. So if my boat is water tight, safe and serves my purposes, without regard for resale value, it's Good Enough.
As a side note, in honour of another friend, I plan to name her dingy "Plan B"

Pole and leg details





Sorry about formatting, I am having trouble with Blogger today

Table leg



This post is to show some of the construction details on how I ended up



Base of table leg

Building some of the bits and pieces, such as the table leg that will also become a horizontal support when everything is folded down to create a large flat space. An additional piece of plywood about 6" wide will be attached to the upper side of the leg (when it is in the horizontal position)

Table leg horizontal

When a large flat space is desired, the table is lowered, the table leg is put in place across to the settee, the settee is pulled out 9", and the two seat backs are placed between the table and settee.This will give an area thirteen feet long and six and a half wide. the cushions will not cover this area completely, so will probably be stacked off to the side. The surface will match the height of the galley sole, so a 24" wide by twenty foot long area is also possible.

















top of pole outboard, with barrel bolt detail



There is a removable pole that holds the inboard forward end of the dinette seat back, cut to hold the seat angle formed with three inches of lean back. the middle of the pole is 1.5 x 1.5 inches, rounded to a nice to grip shape.

Rough cut seat back, still needs rounded edges

Fuzzy picture of pole in place

mortise and tenon

tenon on bottom of pole and matching cutout in the plywood seat bottom. This piece of plywood will be glued down to the seat frame. 

top of pole,inboard

I added a bit of wood at the top to center the barrel bolt in the beam 

Finally, this under the aft end of the settee, this is where the fans to circulate hot air from above the stove around the bunk to under the dinette will be located. I have not picked up the fans, so no holes are cut yet 

Bunk progress & Oops, March 18, 2016

Progress has been slower than ideal, I have been dealing with my domestic hot water heater, and work for some reason expects me to show up if I want to get paid, but at least I can bank some of the overtime. I cut the two 3/4 inch pieces of plywood that make up the bunk, although I need to decide how to lift them up (do I cut a hand hold, attach a strap or something else?) and trim the edge that will hit the crosspiece when being opened.
   The other detail I discovered was the the top port side of the saloon to bunk bulkhead is 1" farther forward than the rest of the bulkhead. Unfortunately, I have glued enough bits at the bottom and cut the pieces on the bunk side to fit that I will not be able to completely correct this without a lot of work. Luckily, it is a cosmetic problem, not structural, so other than adding time while I adjust cuts in the area to the actual rather than theoretical dimensions, it is not that big a deal.
Also, the cross piece midway up the bunk to front hold bulkhead, is slightly crooked, but will easily do its job of reinforcing where the deck on the front attaches, and strengthening the area where the front tabernacle will attach

Air vent under bunk routing Feb 27 2016

 Today's progress was putting in supports to hold up the bunk. A while back, I was having an e-mail conversation with Dave Z, about a clever idea I saw in one of the Junk Rig Association magazines, where someone in a northern boat was finding his feet cold while visiting mid winter. His solution was to make a tube of cloth with a small fan at one end, blowing  heat from up by the roof down to the floor. Dave said he was thinking about an air passage from under the dinette, around the bunk, and up beside the wood stove. Here is my interpretation of that, in progress.

Here are the air holes, from either side, penetrating the port side saloon to bunk bulkhead. I am doing a balancing act in their location, wanting a location out of the way of storage, without weakening the bulkhead too much. There is about 10 square inches of  air hole, as well as a limber hole.

A second layer of plywood will be screwed to the outside, so it is removable for annual painting and  cleaning. This will give a 3 inch wide channel, about 8 inches high across the foot of the bunk. It's amazing how much time is consumed trying to figure out these little details. Hopefully everything will work and I will get toasty warm toes when running the wood stove

Stringers and stuff to Feb 15 2016

Stringers, Feb 2016

Previously, I installed 1.5" insulation in the floor, with 2X4 stringers reinforcing the insulation where the bulkheads cross and furniture edges are to be installed. The plywood was cut so that the seams would be hidden under furniture edges. Here is a picture with the insulation dry fit, it was glued in with Gorilla glue  with a layer of 1/2 inch ply on top. The bulkheads were then screwed and glued to the floor, with temporary braces across the top to hold everything square.

This weekends accomplishment was to install stringers made from two 2x6 planks scarfed together for a total length of twenty five feet on one side, and twenty three and change on the other side ( the side door is located at the end of the starboard one).

Starting with a picture of my scarfing jig, which is a 8:1 slope on some scrap plywood, and a piece of plexiglass that replaces the factory base on my router. An ideal plexi base would be a couple of inches wider, as I have to turn the router at an angle so it doesn't slip off the guides.

Completed scarf prior to glue up

I put short pieces of 2X6 on the sides of the bulkheads, to hold the main stringer, and to act as a nailing surface for the inside plywood pieces.

The size and height of the stringer has been chosen so that the joint in the outside plywood layer, the top of the outside reinforcing plywood, the rub/guard rail, the main level of interior furniture and interior plywood all attach to it.

I noticed that Dave Zeiger has added me to his sidebar, thank you Dave! How many other triloboats are under construction out there?